How to Build a Dog Dish Stand | Generation Next | Ask This Old House

Ask This Old House general contractor Tom Silva teaches a young woodworker how to build a dog dish stand using primarily power tools. #ThisOldHouse #AskTOH SUBSCRIBE to This Old House: http://bit.ly/SubscribeThisOldHouse Time: 1-2 hours Cost: $20 and up Skill Level: Moderate Tools: Miter saw [https://amzn.to/38zpJHH] Drill press [https://amzn.to/37GFwDc] or drill driver [https://amzn.to/2V19Upl] Jigsaw [https://amzn.to/2P5uMIb] Compass [https://amzn.to/2SD79cd] Pocket hole jig [https://amzn.to/39JpKcb] Palm sander [https://amzn.to/2Hz9gav] Shopping List: Food bowls [https://amzn.to/326nGIy] 1x10 pine [https://ift.tt/3a1PQrg] 1x12 pine [https://ift.tt/2PgWHoy] Wipe-on polyurethane [https://amzn.to/37GScdk] Rag [https://amzn.to/37GGY8C] Pocket screws [https://amzn.to/39NLhAK] Steps: 1. Start by cutting the 1x10 boards to size on the miter saw to act as the two legs. 2. Cut the 1x12 board to size on the miter saw to act as a top. 3. Outline an arch on the bottoms of the two legs to give them more shape. Using a drill or a drill press, drill two pilot holes at the top edges of each arch so you’ll have a consistent, rounded edge. 4. Cut out the remaining wood inside the arch using a jigsaw. 5. Use a compass to trace out holes on top of the 1x12 piece to hold the food bowls. Make sure the holes are wide enough to fit the bowls, but not so wide that the lips of the bowl won’t catch on the top. 6. Drill pilot holes in the top of the bowl to fit the jigsaw blade in. 7. Cut out each circle for the top of the dog dish stand using the jigsaw. 8. Assemble the stand using pocket hole screws. After drilling the pocket holes but before screwing everything together, give all the boards a good sanding. 9. Apply a wipe-on polyurethane to the sand using a rag. Resources: Tom taught Camilla to build the dog dish stand out of materials that can easily be found at any home center. For the legs and top, Tom used 1x10 and 1x12 select pine, which can be found at the home center. He bought boards with two separate dimensions so that he didn’t have to use the table saw, which is a more advanced tool for children. To cut the boards to length, Tom had Camilla use the Kapex 120 sliding compound miter saw [https://amzn.to/37FB6MQ], which is manufactured by Festool (https://ift.tt/2tQPgLS). To cut the holes in the legs and for the dog bowls, Tom had Camilla use a jigsaw with a fine tooth cutting blade [https://amzn.to/38IGdNK]. To assemble the stand, Camilla used the Kreg Jig K4 pocket hole jig set [https://amzn.to/2wtDh9x], which is manufactured by Kreg Tools (https://ift.tt/1CCEfcw). For the finish, Tom and Camilla applied a Watco Wipe-On Polyurethane [https://amzn.to/37GScdk] with a rag, which is manufactured by Rust-oleum (https://ift.tt/2pexNYn). The dog dishes can be found at any pet supply store. About Ask This Old House TV: Homeowners have a virtual truckload of questions for us on smaller projects, and we're ready to answer. Ask This Old House solves the steady stream of home improvement problems faced by our viewers—and we make house calls! Ask This Old House features some familiar faces from This Old House, including Kevin O'Connor, general contractor Tom Silva, plumbing and heating expert Richard Trethewey, and landscape contractor Roger Cook. Follow This Old House and Ask This Old House: Facebook: http://bit.ly/ThisOldHouseFB Twitter: http://bit.ly/ThisOldHouseTwitter http://bit.ly/AskTOHTwitter Pinterest: http://bit.ly/ThisOldHousePinterest Instagram: http://bit.ly/ThisOldHouseIG Tumblr: http://bit.ly/ThisOldHouseTumblr Keywords: This Old House, Ask This Old House, DIY, Home Improvement, DIY Ideas, Renovation, Renovation Ideas, How To Fix, How To Install, How To Build, Tom Silva, GenerationNext, woodworking, pets, dog dish stand Watch the full episode: https://ift.tt/2GJYwpo How to Build a Dog Dish Stand | Generation Next | Ask This Old House https://www.youtube.com/user/thisoldhouse/